Prius red triangle no codes

My code came back in less than 30 seconds. "The first step is to clear the P3009 trouble code by unhooking the 12V battery for a moment or using a code reader. Now turn the key on/ but NOT start/ready mode, wait 30 seconds and if the code comes back, the leak is in the battery case. If the code does not return, turn key to start to "ready mode ...

Prius red triangle no codes. First it was the master break solenoid, got that replaced. Car drove fine but the light came up. Just had a shop diagnose it and said it was the inverter coolant for the main hybrid battery. Replaced it but the triangle is still there. My OBD2 reader is showing no codes. I remove the the triangle using the dongle but it comes back up immediately.

The simplest way to reset a warning light in a Prius is to disconnect the 12V battery. This will erase the stored codes and reset the warning light. To do this, locate the battery in the engine compartment, remove the negative cable, wait a few minutes, and then reconnect the cable. 2. Use a Scanner Tool.

On June 20 it stopped cooling almost entirely and I got the red triangle with the exclamation flashing with the word "problem" and beeping. I took it to the dealer who checked it and said that I was out of freon ($250). They said there were no codes and they didn't know why I had the red triangle. It cooled again, but was still intermittent.2008 Prius. Model: N/A. 2008 Prius 230,000 just purchased months ago. Just drove down Mount Washington, which pushed my traction battery all the way full, almost never happens. Couple hours later while on the expressway, the Red Triangle, CEL, and red car with exclamation point came up, I think I was in cruise control because it hesitated.I just got the P1116 and P1121 codes recently and plan to do the following: 2008 2nd Gen with 168K miles purchased in 2008 with 15K miles on it. All parts new Toyota OEM. ENGINE ITEMS-drain system-water pump-thermostat + gasket-serpentine belt-refill with SLLC INVERTER ITEMS-drain system-water pump-refill with SLLC Finally, Clear codes either with my scan reader or disconnecting negative ...About a week ago red triangle, vsc, and check engine light came on. Changed oil (4,800 miles since last), lights still on. Went to Auto zone, checked codes but nothing came up. For no real reason, I decided to reset the codes. They stayed off for about a week then just came back yesterday.Vehicle: 2004 Prius. Depending on fault light will go off when fault condition goes away. If it’s real fault battery is just at the edge of setting fault so it may improve a bit or be just coincidence. But light will be back. If it’s just false code it probably showed fault condition only for small part of second.P3000 code indicates the problem with your Prius' battery or with the total control system. Reasons behind the Red Triangle of Death. Curious about the "Red Triangle of Death"? It's not just any symbol—it's your car's way of talking. Join us on a journey to uncover why it's so intriguing! Check for Warning LightsRed triangle immediately after oil change [2008] Had my oil changed today and after leaving the shop, the car sputtered through the light and barely powered into the next parking lot. Got the red triangle, VCS, the yellow circle and exclamation and check engine. I have a cheap ODBII and Carista, I pulled the codes, but didn't realize there wasn ...

Alright, my friends, it's time to roll up our sleeves and tackle the red triangle head-on. Follow these simple steps to reset the red triangle Prius and get your dashboard looking pristine again: Identify the problem: Before you can reset the red triangle, you need to know what triggered it in the first place. Check your owner's manual for ...Your VSC light staying on means that the Toyota Prius's VSC system has been deactivated. It is not as safe to drive without it on, but it should still drive fine. Good luck determining what is causing the problem. Remember, a good code scanner can save a ton of time. The VSC (Vehicle Stability Control) system is a traction/stability control ...Oh my! | Toyota Prius Forum. Red triangle! Beeps! Curses! Oh my! Just as we were packed up for a trip up the coast to Solvang, my baby flaked on me! I put her in ready mode, and when I shifted to D, I got the dreaded red triangle, a constant beeping, and a message to the effect, "You must shift to Park; the battery will not be charged in ...The P0446 is what has been causing the check engine light to pop on every month or so for about 6 months now, and thats also what came up today. When I cleared that code, it cleared the check engine light as well as the red triangle, neither have come back on. #3 TeamPriusNewbie, Mar 3, 2024.Vehicle: 2006 Prius. Model: N/A. I have a 2006 Prius with 165,000 miles. I put a new OEM Toyota hybrid battery at the beginning of June and the car has run as normal. A couple weeks ago after maybe 5 minutes on the road, we got the red triangle of death and assorted other lights. This was maybe the coolest weather we've had in a this fall (in ...2001 Prius, Red Triangle, Check Engine Light, PS + Battery+Car red exclamation alert. Discussion in 'Generation 1 Prius Discussion ... A code reader is needed to do that. Most generic ones are useless on a Gen 1 Prius, because they will only show codes from a couple computers (engine and possibly brake) and totally ignore the …

The simplest way to reset a warning light in a Prius is to disconnect the 12V battery. This will erase the stored codes and reset the warning light. To do this, locate the battery in the engine compartment, remove the negative cable, wait a few minutes, and then reconnect the cable. 2. Use a Scanner Tool.> Gen 2 (2004-2009) Toyota Prius Forums > Gen 2 Prius Care, Maintenance and Troubleshooting > Server migration is complete! Check out this thread for more details and to report any bugs .My daughter recently bought a 2006 Prius with 170K, Car was running great at purchase time with no issues but unfortunately the honeymoon was short lived. Less than 50 miles, she got the check engine light and red triangle. Car seems to still to drive fine. Had a dealer near Knoxville TN pull the codes and the only code was a P0A9C - Hybrid ...read the codes; read the codes; read the codes; If those lights came on, there were codes. The codes that make those lights come on are not in the computers you can read with a generic scan tool. A Prius-aware scan tool is one that can read the rest. It costs more than a $10 multimeter but less than a kick-nice person one.Alright, my friends, it's time to roll up our sleeves and tackle the red triangle head-on. Follow these simple steps to reset the red triangle Prius and get your dashboard looking pristine again: Identify the problem: Before you can reset the red triangle, you need to know what triggered it in the first place. Check your owner's manual for ...

Mayan santikos.

I hooked it up to a mini-vci with techstream and found the following: P3009-526, C1310 and B1421. The car will only start if you reset codes, then after a few minutes of running the red triangle comes back. The car runs perfect with absolutely no shuddering and gas mileage is normal. -Tested all 28 modules.> Gen 2 (2004-2009) Toyota Prius Forums > Gen 2 Prius Care, Maintenance and Troubleshooting > Attachments are working again! Check out this thread for more details and to report any other bugs. ... Need to get your codes to see what is throwing Red Triangle. Also 12v health is one thing to consider. The coolant side water …The Master Warning Light, which too often gets called the "red triangle of death", is a generic warning light that comes on whenever the hybrid-vehicle ECU has any trouble codes to report. ... Gen 2 Prius does store permanent codes but starting with 2010 vehicles the PDTCs are now stored in NV Ram so disconnecting the 12v battery or using a ...3- Wait 30 minutes. 4- Make sure all doors are closed. 5- Reconnect battery Cables. 6- Lock & unlock the vehicles using the key from driver door side (if you have a key fob with no blade key, just lock & unlock using the key fob buttons) 7- Enter the vehicle and attempt to start and see if it will go away.> Gen 2 (2004-2009) Toyota Prius Forums > Gen 2 Prius Care, Maintenance and Troubleshooting > Server migration is complete! Check out this thread for more details and to report any bugs. Red Triangle, no codes again. Discussion in 'Gen 2 Prius Care, Maintenance and Troubleshooting' started by Nance459, Jan 24, 2023. Page 2 of 2 < Prev 1 2.

Jan 26, 2021 · > Gen 2 (2004-2009) Toyota Prius Forums > Gen 2 Prius Care, Maintenance and Troubleshooting > Server migration is complete! ... Red Triangle, no codes again. 2008 Prius. Model: N/A. 2008 Prius 230,000 just purchased months ago. Just drove down Mount Washington, which pushed my traction battery all the way full, almost never happens. Couple hours later while on the expressway, the Red Triangle, CEL, and red car with exclamation point came up, I think I was in cruise control because it hesitated. At 60 miles an hour, the red triangle and check engine light. At 60 miles an hour, the red triangle and check engine light come on. They indicate it is a hybrid cooling pump and the stability control system. … read more. Ted Ritter. High School or GED. 12 votes, 19 comments. 39K subscribers in the prius community. Everything Toyota Prius! ... I'd get an OBD II scanner and check for codes. It can mean the coolant pump has failed, for example, which can lead to destroying your engine. ... My 2005 is still running strong at 162k, everyday I'm waiting for the imenent red triangle of death lolBelow is the best information and knowledge about how to reset prius red triangle light compiled and compiled by the BMR team, along with other related topics such as: 2007 prius red triangle and check engine light, 2008 prius red triangle and check engine light, prius red triangle comes and goes, 2008 prius red triangle with exclamation point, prius red triangle no codes, 2008 prius warning ...Model: N/A. I purchased my 2001 Prius used with 175k miles on it it currently has 185k. Today while driving I heard a loud beep followed by the Warning/Problem sign on my in-dash monitor followed by a red car symbol with exclamation as well as a Check Engine and Red Triangle. I took it down to AutoZone to get a scan on the code but after 3 ...This indicates a problem with the regenerative braking, and is triggered by the above code. A symptom rather than a cause. c1310. I don't see that as a valid code for a GenII Prius. c2318. "Low voltage error" comes with the failed 12V battery. b1421. This can be ignored. (Light sensor on dash.)Attention automakers: You’re doing it all wrong when selling your hybrid cars. Those Toyota commercials featuring R&B singer Raphael Saadiq and hipsters grooving in a Prius V? Not ...2008 Toyota Prius with ~270000 miles on her. Today randomly the red triangle of death popped up along with these 2 codes according to auto zone.0. Vehicle: Other Hybrid. Model: N/A. Check to see if your rear hatch is closed tightly. You will see the red trangle if you open a door while the car is in Drive. Since you had an intermittent alarm, it could be a door not closed properly. #2 firepa63, Sep 23, 2009.A 2006 Prius with 158,082 miles on it. A few weeks ago I felt it driving funny and then all my lights came on including the red triangle, check engine, and caution light. I took it to the dealership and was given this list of codes: P3000-----battery control system P3102-----transmissions control ECU P3108-----lost com.

After engaging the safety interlock, it would take 3 on/off cycles to clear the red triangle and the fault code would go into "historical" status. Disconnecting the battery accomplishes the same thing and totally clears the fault memory. Glad to hear everything is up and running again. #16 TMR-JWAP, Dec 2, 2019.

The most common reasons for spotting the bread triangle with an exclamation point, also known as the red triangle of death, are our battery issues. However, oil issues can also make this warning sign appear on your vehicle’s dashboard. If you have an ODB reader, you’ll be able to test the health of the Hybrid battery yourself. by. Eric ...2005 Prius with about 160k miles. Red Triangle and the P3000 code came up. Powers on with all the dash lights and monitor, no start though. Could it be...Hello everyone Recently purchased a 2006 prius w/ 152,000 miles on it. Im currently getting the "red triangle of death." Im currently getting the "red triangle of death." I was told to check the Hybrid battery cells with …11 votes, 24 comments. 41K subscribers in the prius community. Everything Toyota Prius! ... Red Triangle + yellow engine, brake, then 3 letters I forgot + MFD with upper left red Car With Exclamation Mark. ... Workshop tried to clear the codes to no avail, and since I replaced the 12v battery, the car stayed overnight without it (which did ...2006 Prius. Model: ----USA----. I have a 2006 Toyota Prius with 182,000 miles on it. Yesterday when going to lunch I started my car and the Red Triangle, Check Engine, Circle with Exclamation Mark, the little red car with exclamation mark on the display and VSC lights all came on. On my way home from work I stopped and picked up a new 12v ...Location: boston. Vehicle: 2012 Prius Plug-in. Model: Plug-in Base. sounds like your battery is bad again. perhaps the auto zone scanner isn't picking up the codes. i have not heard of the cooling fan being triggered by the dash lights, it likely is the battery overheating. #2 bisco, Sep 26, 2016.Jan 26, 2021 · > Gen 2 (2004-2009) Toyota Prius Forums > Gen 2 Prius Care, Maintenance and Troubleshooting > Server migration is complete! ... Red Triangle, no codes again.

Finger monkey for sale new york.

Lyssiebbygirl16.

The red stuff all over everything is 100% synthetic grease to prevent corrosion. Works great. The extra red lead on the 12 volt terminal is for a towing light aux power supply. Sometimes after you restart the car it will show alot of codes that's ok just shut the car off and start again there will be no codes.Red Triangle, ABS, VSC, Check Engine, Will not go ready and does not show codes. Discussion in 'Gen 2 Prius Main Forum' started by deegee, Jul 6, 2021. deegee New Member. Joined: Jul 6, 2021 6 1 0 Location: Georgia Vehicle: 2006 Prius Model: V. My daughter bumped her 2006 Prius into an SUV in front of her. No one was hurt.Hi all, I bought a 2007 Prius a few months ago for cheap off my neighbor. It had a reconditioned battery put in about two years ago. Last week it showed the red triangle of death, and I got a P0AA6 code on my reader. Scheduled it at the mechanic for this week, but I had to clear the code in order to put it in drive to get it to the shop.The "death" triangle might indicate that you need a new 12V battery. A new battery fixed my problem on my old 2008. YouTube has instructions how to do it. Basically all you need is a 10mm socket and a bit of patience. #5 plug-it-in, Jun 20, 2016.We replaced the mfd. worked for 3 weeks. Back to Prius at a rave and black triangle. Found a second salvaged mfd and replaced it again (because the first was salvaged, you never know) 1 week later back to the same old tricks (flashing mfd and red triangle, no modules talking) So.... tore the entire car apart checking for grounds and loose connections (because when it failed the last time I got ...I have 2008 Prius with 126k miles on it. I was driving at highway and three lights ( red triangle, yellow circle with ! and the red car with the ! on the display) came on. I didn't stop right away. After 2-3 minutes car shut down and never start again. Inside lights and signals were okay and bright. But even I put the key in, car didn't response.165 Answers. The red triangle is the Master Warning light may also be referred to as hybrid system erro warning light. You must have had an intermit problem with the battery system for the light to come on and go off. You should take the car to a shop or dealer that works on them systems to see if it stored a code so you will have an idea what ...There are four (4) types of labeling for DTCs; Stored, Pending, Current and Permanent. The required conditions for DTC P0A80 were met during a drive cycle, and the red triangle illuminated. Once the conditions that trigger P0A80 are no longer met and after three (3) drive cycles, the red triangle will turn off, and the code is then "Stored" in ...Hello, I have a 2005 Prius. I have been getting normal gas mileage and haven't seen any new issues. However, the red triangle and check engine light both popped on. I took it to a shop that checked the code and he said that it was odd because no codes were popping on. He said that he had heard about that happening to people when … ….

> Gen 2 (2004-2009) Toyota Prius Forums > Gen 2 Prius Care, Maintenance and Troubleshooting > Attachments are working again! Check out this thread for more details and to report any other bugs. Ema - Red Triangle, No Gas Engine, No Codes Thrown? Discussion in 'Gen 2 Prius Care, Maintenance and Troubleshooting' started …When the light turns on briefly during normal operation, it means your Prius is losing traction—and the system’s fighting hard to maintain it. But if that light stays on, or if you see a light that says “VSC OFF” or “TRAC OFF,” you’re likely dealing with a different problem. These lights mean that your VSC system is off ...I just got the P1116 and P1121 codes recently and plan to do the following: 2008 2nd Gen with 168K miles purchased in 2008 with 15K miles on it. All parts new Toyota OEM. ENGINE ITEMS-drain system-water pump-thermostat + gasket-serpentine belt-refill with SLLC INVERTER ITEMS-drain system-water pump-refill with SLLC Finally, Clear codes either with my scan reader or disconnecting negative ...> Gen 2 (2004-2009) Toyota Prius Forums > Gen 2 Prius Main Forum > Generation 1 Prius Discussion > Attachments are working again! Check out this thread for more details and to report any other bugs .On this Toyota Prius, we found water intrusion causing a problem with a wiring connector for the hybrid battery pack cooling fan. The water caused the termin...I have 2008 Prius with 126k miles on it. I was driving at highway and three lights ( red triangle, yellow circle with ! and the red car with the ! on the display) came on. I didn't stop right away. After 2-3 minutes car shut down and never start again. Inside lights and signals were okay and bright. But even I put the key in, car didn't response.The day the triangle lit up, with it came the yellow VSC light, the yellow brake warning light and the check engine light. The computer shuts you out of the ability to use the cruise control, and the top 1/2 inch of the information display is changed to show an outline car, in red, with an exclamation mark inside.2006 Prius Red triangle ! Rear fan blowing when start the car Red car and ! on center display vsc light Circle with exclamation Check engine The AC needs to be replaced Codes: P1116, P1121 167,000 miles The car starts and the rear fan goes on right away. We changed The 12 volt battery all warning lights still on. The car lags, will go 10 mph then up to 40 mph no power uphill. Prius red triangle no codes, [text-1-1], [text-1-1], [text-1-1], [text-1-1], [text-1-1], [text-1-1], [text-1-1], [text-1-1], [text-1-1], [text-1-1], [text-1-1], [text-1-1], [text-1-1], [text-1-1], [text-1-1], [text-1-1], [text-1-1], [text-1-1], [text-1-1], [text-1-1], [text-1-1], [text-1-1], [text-1-1], [text-1-1], [text-1-1], [text-1-1], [text-1-1], [text-1-1], [text-1-1], [text-1-1], [text-1-1], [text-1-1], [text-1-1]